Results 1 to 8 of 8
Thread: Tamiya Nitrage part needed
-
04-06-2014, 05:08 PM #1
Tamiya Nitrage part needed
Hi all, I'm looking for a starter assembly that goes on the back of a Tamiya Nitrage engine. The part that the Handy start fits into to start the engine. I can't find one anywhere.
Any ideas?Come to Lake Centenary in Temora to run your RC boat. Free BBQ's, power points, great amenities with hot showers, a childs sandpit/play area and lots of shade sails around the lake edge. It's 2km out of town, fresh water and gas boats are welcome. -
Sponsored Links Remove Advertisements
-
04-06-2014, 08:55 PM #2
Pull Start maybe....
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Baja...Because Size Matters!
Everybody is adding famous quotes to their sigs, so...My Mother to my Father on Disciplining me as a child....You hit him Noel, My Arm is getting tired. -
04-06-2014, 09:09 PM #3
That would do. I don't know what would fit it though.
Come to Lake Centenary in Temora to run your RC boat. Free BBQ's, power points, great amenities with hot showers, a childs sandpit/play area and lots of shade sails around the lake edge. It's 2km out of town, fresh water and gas boats are welcome. -
Sponsored Links Remove Advertisements
-
04-06-2014, 09:19 PM #4
Is it the 5.2 nitro engine Brett?
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Baja...Because Size Matters!
Everybody is adding famous quotes to their sigs, so...My Mother to my Father on Disciplining me as a child....You hit him Noel, My Arm is getting tired. -
04-06-2014, 09:34 PM #5
Yes Pete. That's the one. Maybe a Force .32 pull start would fit but I'm not sure.
Come to Lake Centenary in Temora to run your RC boat. Free BBQ's, power points, great amenities with hot showers, a childs sandpit/play area and lots of shade sails around the lake edge. It's 2km out of town, fresh water and gas boats are welcome. -
05-06-2014, 11:20 AM #6
What's the bolt spacing and OWB size brett? I have a few rotor start plates here I have no use for, one of them may fit
Sent from my LG-P705 using TapatalkOnly Aero based now, mostly multi rotors and FPV Turnigy Talon-X, Scratch Built Tri, Scratch built Deadcat
900mhz and 5.8g FPV Setups, Custom Clover Leaf aerials
Anyone need CAD (Solidworks) designs done PM me, all i need is a rough sketch. No Charge for simple designs. -
05-06-2014, 11:24 AM #7
I'll measure tonight. The car is in a container on the farm where we run. Cheers.
Come to Lake Centenary in Temora to run your RC boat. Free BBQ's, power points, great amenities with hot showers, a childs sandpit/play area and lots of shade sails around the lake edge. It's 2km out of town, fresh water and gas boats are welcome. -
30-10-2014, 11:58 AM #8
Still Looking.
Anyone?Come to Lake Centenary in Temora to run your RC boat. Free BBQ's, power points, great amenities with hot showers, a childs sandpit/play area and lots of shade sails around the lake edge. It's 2km out of town, fresh water and gas boats are welcome.
Similar Threads
-
Tamiya Nitrage 5.2
By PC WIZ in forum General Talk - R/CReplies: 6Last Post: 09-10-2012, 12:35 AM -
Tamiya Nitrage
By PC WIZ in forum Monster Truck - Nitro 1/8 ScaleReplies: 27Last Post: 27-01-2010, 12:49 AM -
Traxxas Slash 1/16 VXL part needed
By rcpilot in forum Stadium Trucks - ElectricReplies: 4Last Post: 10-01-2010, 01:52 AM -
Hyper ST- Tamiya Nitrage- HPI Hellfire
By miker in forum Truggies - NitroReplies: 16Last Post: 27-09-2007, 11:37 AM